Application instruction
If the instructions are unclear or missing for your product, we encourage you to contact us directly.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 12-15 drops of AQUA COATING ONE on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Remove Excess Product
Wait approximately 1 minute, then use a microfiber towel to remove any excess product. Follow up with a second microfiber towel to polish the surface to a high gloss. Inspect for any imperfections before moving on to the next panel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period.
5. Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 2-12 hours after the final layer of AQUA COATING ONE.
Additional Application Tips
- Warm Conditions
In warmer temperatures (68°F/20°C and above), the coating will dry more quickly. Apply to smaller areas and test in an inconspicuous area, such as a bumper, to find the ideal flash time. - Microfiber Towels and Applicators
Change applicator and microfiber towels as needed. Use fresh microfiber towels for each section to avoid residue buildup. Use the dedicated AQUA APPLICATORS for optimal results. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Layering
For additional protection, two layers can be applied. A single layer of AQUA COATING ONE provides 12-18 months of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible – this is far less damaging than allowing dirt to sit on the surface.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 12-15 drops of AQUA COATING 9H on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Remove Excess Product
Wait approximately 30-60 seconds, then use a microfiber towel to remove any excess product. Follow up with a second microfiber towel to polish the surface to a high gloss. Inspect for any imperfections before moving on to the next panel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period. - Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 2-12 hours after the final layer of AQUA 9H COATING.
Additional Application Tips
- Warm Conditions
In warmer temperatures (68°F/20°C and above), the coating will dry more quickly. Apply to smaller areas and test in an inconspicuous area, such as a bumper, to find the ideal flash time. - Microfiber Towels and Applicators
Change the applicator and microfiber towels as needed. Use fresh microfiber towels for each section to avoid residue buildup. For optimal results, use the dedicated AQUA APPLICATOR. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Layering
For additional protection, two layers can be applied. A single layer of AQUA COATING 9H provides 2+ years of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible—this is far less damaging than allowing dirt to sit on the surface.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 12-15 drops of AQUA COATING 9H PRO on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Remove Excess Product
Wait approximately 15-30 seconds, then use a microfiber towel to remove any excess product. Follow up with a second microfiber towel to polish the surface to a high gloss. Inspect for any imperfection before moving on to the next panel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period. - Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 3-12 hours after the final layer of AQUA COATING 9H PRO.
Additional Application Tips
- Warm Conditions
In warmer temperatures (68°F/20°C and above), the coating will dry more quickly. Apply to smaller areas and test in an inconspicuous area, such as a bumper, to find the ideal flash time. - Microfiber Towels and Applicators
Change the applicator and microfiber towels as needed. Use fresh microfiber towels for each section to avoid residue buildup. For optimal results, use the dedicated AQUA APPLICATORS. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Layering
For additional protection, two layers can be applied. A single layer of AQUA COATING 9H PRO provides up to 4 years of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible—this is far less damaging than allowing dirt to sit on the surface.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 12-15 drops of AQUA GRAPHENE COATING on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Summer Application. Remove any excess product residue immediately with the first microfiber towel.
Fall/Winter/Spring Application. Wait approximately 20-30 seconds before removing the excess product with the first microfiber towel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period. - Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 4-12 hours after the final layer of AQUA GRAPHENE COATING.
Additional Application Tips
- Warm Conditions
In warm conditions (68°F/20°C and above), it’s best to apply the coating to smaller areas initially. Adjust the
application area and product amount based on the product’s flash time on the paint. Test on a less
visible area, like the bumper, to determine the best application method. - Microfiber Towels and Applicators
Replace the microfiber applicator as needed, and do not use it for more than 20 minutes per session. Use fresh microfiber towels for each section to avoid residue buildup. Use the dedicated AQUA APPLICATORS for optimal results. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Layering
For additional protection, two layers can be applied. A single layer of AQUA GRAPHENE COATING provides 3 years of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible—this is far less damaging than allowing dirt to sit on the surface.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 15 – 20 drops of AQUA E-COATING on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Summer Application. Remove any excess product residue immediately with the first microfiber towel.
Fall/Winter/Spring Application. Wait approximately 15-30 seconds before removing the excess product with the first microfiber towel. - Remove Excess Product
Follow up with a second microfiber towel to polish the surface to a high gloss. Inspect for any imperfection before moving on to the next panel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period. - Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 4-12 hours after the final layer of AQUA E-COATING.
Additional Application Tips
- Warm Conditions
In warm conditions (68°F/20°C and above), it’s best to apply the coating to smaller areas initially. Adjust the
application area and product amount based on the product’s flash time on the paint. Test on a less
visible area, like the bumper, to determine the best application method. - Microfiber Towels and Applicators
Replace the microfiber applicator as needed, and do not use it for more than 20 minutes per session. Use fresh microfiber towels for each section to avoid residue buildup. Use the dedicated AQUA APPLICATORS for optimal results. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Durability
A single layer of AQUA E-COATING provides 4 years of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible—this is far less damaging than allowing dirt to sit on the surface.
Note
The visible suspension in the coating is a natural feature and does not impact the installation process or coating durability.
Preparation
- Prep Wash & Decontamination
Thoroughly wash and decontaminate the vehicle. Use AQUA BLOODY IRON for chemical decontamination, and clay bar treatment on painted surfaces to remove bonded contaminants. - Paint Correction
Machine paint correction is recommended to remove imperfections and create a smooth surface. - Degrease
Use AQUA PANEL PREP and a microfiber towel to remove any residue.
Application Instructions
- Prime the Applicator
Place 15 – 20 drops of AQUA E-COATING PRO on a microfiber applicator. Apply the coating in an even, thick, and wet layer. After the initial priming, use fewer drops for subsequent applications. - Apply the Coating
Use crosshatch strokes (horizontal and vertical) to apply the coating. For large panels, such as the hood or roof, divide them into sections for better control. - Summer Application. Remove any excess product residue immediately with the first microfiber
towel.
Fall/Winter/Spring Application. Wait approximately 15-30 seconds before removing the excess
product with the first microfiber towel. - Remove Excess Product
Follow up with a second microfiber towel to polish the surface to a high gloss. Inspect for any imperfection before moving on to the next panel. - Cure Time
After applying the coating to all panels, allow the coating to cure for 24 hours in a dry, stable environment. Ensure temperatures remain above 50°F (10°C) during this period. - Enhance with Coating Booster
For maximum durability, apply AQUA COATING BOOSTER between 4-12 hours after the final layer of AQUA E-COATING PRO.
Additional Application Tips
- Warm Conditions
In warm conditions (68°F/20°C and above), it’s best to apply the coating to smaller areas initially. Adjust the
application area and product amount based on the product’s flash time on the paint. Test on a less
visible area, like the bumper, to determine the best application method. - Microfiber Towels and Applicators
Replace the microfiber applicator as needed, and do not use it for more than 20 minutes per session. Use fresh microfiber towels for each section to avoid residue buildup. Use the dedicated AQUA APPLICATORS for optimal results. - Lighting
Use adequate lighting to monitor application and ensure even coverage. - Moisture and Weather Protection
Keep the coated surface dry for 24 hours post-application. Avoid harsh weather for the first 7 days. - Application Conditions
Do not apply in direct sunlight, rain, or on a hot or damp surface. - Durability
A single layer of AQUA E-COATING PRO provides 5 years of protection. - Temperature Stability
Ensure the application environment stays above 50°F (10°C). - Safety Measures
Wear appropriate personal protective equipment (gloves, face mask) during application.
Maintenance & Storage
- Washing
Hand-wash the vehicle every two weeks, or as needed, with a high-quality, neutral pH soap to maintain the coating’s integrity. Wash in the shade, and use a quality microfiber mitts and drying towels. - Storage
Store unused product in a cool, dry place. Shelf life is 3 years; use within 6 months after opening.
Customer Notice
The primary risk to a fresh, curing coating is dirt. During the two-week curing period, avoid excessive contamination. If the coating does get dirty, gently wash it with a neutral pH soap as soon as possible—this is far less damaging than allowing dirt to sit on the surface.
Note
The visible suspension in the coating is a natural feature and does not impact the installation process or coating durability.
Preparation
- Surface Preparation: Thoroughly wash the wheels using AQUA BLOODY IRON or AQUA APC (diluted 1:10 or 1:15). Degrease the wheel surface with AQUA PANEL PREP, repeating the process twice for optimal results .
Application Instructions
- Application: Apply the coating in straight lines directly onto the surface using a microfiber applicator or AQUA SUADE CLOTH. For larger wheels, you may need to divide them into sections.
- Leveling: Wait approximately 60 seconds, then use a microfiber towel to remove any excess product residue (as the product crystallizes quickly, avoid waiting too long).
- Curing: Allow the coating to cure under dry, stable conditions for 24 hours, ensuring that the temperature remains above 50°F (10°C)
Notes:
- Do not apply AQUA WHEEL COATING in direct sunlight, on hot or wet surfaces, or at temperatures below 50°F (10°C).
- Silver or other light-colored wheels may not require the leveling step; conduct a spot test to confirm the desired outcome.
Maintenance:
- Use AQUA BLOODY IRON or AQUA APC (diluted 1:10 or 1:15) for washing and maintenance.
- Storage: 3-year shelf life; use within 6 months of opening.
- Durability: Provides protection for up to 24 months.
Preparation
- Clean the Glass: Thoroughly clean the glass surface using AQUA GLASS CLEANER.
Application Instructions
- Apply the Coating: Dispense 8-10 drops of AQUA GLASS COATING onto an applicator with a suede cloth.
- First Layer: Apply the first layer using vertical motions, ensuring no spots are missed.
- Second Layer: Immediately apply the second layer using horizontal motions to ensure complete coverage of the glass surface.
- Reapply if Needed: If the applicator starts to feel dry, add a few more drops of the product to maintain even coverage.
- Remove Excess: Allow the product to dry completely (usually 10-15 minutes). Use a microfiber towel to remove any excess product residue.
Curing:
- Allow the coating to cure in dry, stable conditions for a minimum of 12 hours, ensuring the temperature does not drop below 50°F (10°C).
Notes:
- Avoid applying AQUA GLASS COATING in direct sunlight, on hot surfaces, or wet surfaces, and at temperatures below 50°F (10°C).
Storage:
- 3-year shelf life; use within 6 months of opening.
Brak produktów w koszyku.